Latex 315 repair services Southern California
HP Latex 315 Printer Repair, 315 Printer Maintenance Service Error Code Repairs, Latex 315 Repair Los Angeles, Orange County and Riverside County! Latex 315 printer repair Southern California! HP Latex 300 series Latex 315 printer repair and onsite service in Los Angeles and Orange County with broken belt, image defects, error messages, error codes and maintenance errors. We provide fast onsite HP Latex 315 printer maintenance service in Southern California. Our technicians have the knowledge and technical ability to repair latex 315 printer on the first visit. We offer 6 months warranty on all Latex 315 replacement parts in Southern California. We carry most common parts to fix Latex 315 hardware failures with numerical error code on the first visit. We offer latex printer 315 printer service with broken belts and service error messages. We replace Latex 315 ink tubing system and purge the ink tubing system. We offer same-day on-site latex 315 54 and 64 inch belt kit replacement and lubricating the rails and run alignment test. We specialize on repairing Latex 315 printers with maintenance kit 1, M-kit 2 and maintenance kit 3 replacement in Southern California. We offer Latex 315 printer belt kit, carriage assembly, encoder strip, encoder sensor, main, ink supply station, (ISS) hard drive, Power supply, print heads, Rolling pump assembly, aerosol fan, and ink tubing system. Latex 315 / 335 / 365 yearly service contract includes 3 free visits to clean and inspect the latex printer. If your latex 315 printer fails during the 1 year service contract you only pay for parts and the labor is covered. HP 315 Latex Inks and Print Heads Take advantage of the versatile, durable performance of HP Latex Inks:• Scratch resistance comparable to hard-solvent inks on SAV and PVC banner— you can consider un-laminated use for short-term signage9• Prints are completely cured and dry inside the printer, and ready for immediate finishing and delivery• Six HP print heads provide 12,672 nozzles for robust and reliable quality print to print. HP Latex Optimizer Achieve high image quality at high productivity:• Interacts with HP Latex Inks to rapidly immobilize pigments on the surface of the print. High-efficiency curing High-speed printing with less energy and at lower temperatures:10• 17 m2/hr (183 ft2/hr) indoor quality, 31 m2/hr (334 ft2/hr)high-speed outdoor Color consistency Print panels or tiles with excellent color consistency for an edge-to-edge match:• i1 embedded spectra photometer enables automatic calibration12• Delivers consistent colors to <= 2 dE200013quality, 91 m2/hr. (980 ft2/hr.) maximum print speed. Latex 315 Printer System Error Codes Front-panel error codes for Latex 315 printers. Under certain circumstances, a numeric error code appears on the front panel. Follow the advice in the Recommendation column to resolve the error. If the recommendation does not seem to solve the problem, call your service representative. If an error code appears on the front panel that is not included in this list, turn off the printer and then turn it back on. If the problem persists, call your service representative. 03.21:01 PSU under voltage detected. 14.72:01 Zero voltage detected. 14.73:01 Very low voltage detected. 14.74:01 Low voltage detected. 14.75:01 Excessive voltage detected. 14.87:10 Curing power regulator over temperature detected. 16.01:00 the printer is unable to warm up within a preset time limit. 16.02:00 the printer is unable to cool down within a preset time limit. 16.03:00 Excessive heat in the printer. 16.04:00 Insufficient heat in the printer. Check that the ambient temperature is within printer specifications (15–35°C). 16.11:10Curing temperature sensor measurement out of range (temperature sensor 1 failed or not connected). 16.12:10 Curing temperature sensor measurement out of range (temperature sensor 2 failed or not connected). 16.13:10 Curing temperature sensor measurement out of range (temperature sensor 3 failed or not connected). 1 .Turn off the printer.2. Check that the ambient temperature is within printer specifications (15–35°C).3. Check that the electronic enclosures at the rear of the printer are properly ventilated.4. Turn on the printer. 16.14:10 Curing temperature sensor measurement out of range (temperature sensor 4 failed or not connected). 16.84:03, 16.85:03 Air curtain resistor out of range. Check that the air curtain fans (at the front of the curing module) are working and unblocked. 21:13 Unable to move the maintenance cartridge along its whole path. 21.2:10 Maintenance cartridge error.1. Turn off the printer.2. Remove and reinsert the maintenance cartridge.3.Turn on the printer.3. If the error persists, replace the maintenance cartridge. 21.5:03 the part that advances the print-head maintenance cartridge web wipe is blocked. Turn off the printer.1. Remove and reinsert the maintenance cartridge.2. Turn on the printer.3. If the error persists, replace the maintenance cartridge. 25.n:10 25.1:10, 25.2:10, 25.3:10,25.4:10, 25.5:10, 25.6:10, 25.7:10 black ink fault (where n = the ink cartridge number) A possible error in the ink cartridge pressure sensor has been detected. The ink level reported may not be accurate. 27.1:00 several blocked nozzles have been detected in the optimizer print head. If print quality is not acceptable, clean or replace the print-head. 27.n:01 (where n = the print-head slot number) A large number of blocked nozzles have been detected in one or more print-heads. Calibration may have failed due to low print head performance. Clean all the print-heads and check their status. 29:00 the maintenance cartridge (part number CZ681A) is almost full. It will need to be replaced soon 29:01 the maintenance cartridge is not inserted correctly. 29.1:01 Unable to track the maintenance cartridge status. Check, visually, that the maintenance cartridge has a correct status pattern on it 29.2:00 Unable to advance the print-head cleaning roll. Replace the maintenance cartridge. 32:01 the take-up reel is disconnected. If you want to use the take-up reel, turn off the printer and ensure that all take-up reel cables are connected (sensor cables, printer cable). If you do not want to use it, you may need to unload the substrate manually from the take-up reel. Remember to cut the substrate first.32:01.1, 32:01.2 This error occurs when the tension bar stays in one of its sensor trigger positions for more than 8 seconds. The most likely causes of
Latex 315 repair services Southern California Read More »
